The steel wire mesh produced by wire mesh factories in China meets the quality standards: steel wire mesh in shape and steel wire welding in customization. The shape and size of the reinforcing bar net shall be determined by negotiation between the two parties according to the design and construction requirements.

　　形狀網格鋼板鋼筋在兩個方向,但是可以在同一個方向和直徑間隔導致鋼筋應相同的快捷方式,間隔二世,crb550應采用鋼絲網肋下冷軋hrb400級或鋼肋下熱軋級鋼筋的生產,cpb550可能采用光冷拉級鋼筋生產。注:網孔鋼筋技術應符合現行《鋼筋混凝土網孔》gb/t-1499.3 2002的標準要求。

　　The shape grid steel bar is in two directions, but it can lead to the same shortcut in the same direction and diameter interval. The second time interval, the production of cold-rolled HRB400 grade steel bar under steel mesh rib or hot-rolled grade steel bar under steel rib should be adopted in crb550, and the production of cold-rolled grade steel bar under steel rib may be used in cpb550. Note: The technology of mesh reinforcement should meet the national standard requirements of gb/t-1499.3 2002.

　　鋼網片的規格應符合以下規定:網片長度為12米，寬度不得超過3.3米。在小車方向上制作鋼網適宜的間隔為100mm、150mm和垂直生產;200毫米間距的鋼筋應具有補救'降水10毫米為所有排水。網格是縱向加筋的，可以實現加筋形式。雙層鋼筋，雨間距應力鋼筋應不大于10mm。

　　The specifications of the steel mesh shall meet the following requirements: the length of the mesh shall be 12 meters and the width shall not exceed 3.3 meters. The most suitable spacing for making steel mesh in the direction of trolley is 100mm, 150mm and vertical production; the steel bar with 200mm spacing should have the ability to remedy the'precipitation 10mm'for all drainage. The grid is longitudinal stiffened and can be realized in the form of stiffening. Double-layer steel bar, rain spacing stress steel bar should not be more than 10 mm.

　　鋼條直徑:冷軋帶輕拉拔或鋼筋表面長度為12mm與鋼條、冷加4比4的鋼條工人直徑在12mm范圍內0.5 mm采用受力鋼條駕駛座5-12mm;熱軋帶肋鋼駕駛座的吃水為6-16毫米。鋼筋網片的鋼筋強度不應低于標準強度。95%保證率冷軋帶肋鋼筋和冷拔鋼筋的強度按極限規程的標準值端口FSTK表示，確定強度。熱軋帶肋鋼筋的強度標準值是根據fyk、搶取率確定的。

　　Bar diameter: cold-rolled strip light drawing or steel bar surface length of 12 mm and steel bar, cold-added 4:4 steel bar worker diameter in the 12 mm range of 0.5 mm force steel bar driver 5-12 mm; hot-rolled ribbed steel driver's draught is 6-16 mm. The reinforcing bar strength of steel mesh should not be lower than the standard strength. The strength of cold-rolled ribbed steel bar and cold-drawn steel bar with 95% guaranteed rate is expressed by the standard port FSTK of limit specification, and the strength is determined. The strength standard value of hot-rolled ribbed bar is determined according to fyk and grabbing rate.