Generally, we will take a comprehensive look at the quality of the steel mesh before using it. As long as the quality of the steel mesh is good, there will be no problems in the use process. But the quality of grid is not a simple task, so what is the key point of grid quality?

　　建造的傳統方法之外構建網格特征、新金屬材料的使用墻鋼筋鋼絲網,電焊網,使建筑更加鞏固,它可以使各種承重墻,代替磚墻非承重墻和地板,陽臺視圖同時質量通常有以下:真絲外觀，看真絲經紗合格差一般在0.2 mm左右，網眼寬度和孔長不合格，重量、對角線、是否有開焊狀態，焊點是否牢固。

　　In addition to the traditional method of construction, the construction is strengthened by the use of wall steel wire mesh and welded wire mesh, which can make all kinds of load-bearing walls instead of brick wall non-load-bearing walls and floors. The balcony view usually has the following qualities: silk appearance, silk warp yarn qualification difference is generally about 0.2 mm, mesh width. Degree and hole length are not qualified, weight, diagonal line, whether there is open welding state, whether the solder joint is firm.

　　建立鋼網規模,通常由網格規模還不是特別準確,機械仍然是一個單一的要求是更準確,看到的應用程序的需求,一般在5毫米對角線,±2厘米的規模是正常的,所以燒焊,光擴張和收縮將顯示必須是錯的。鋼筋網的絲線經紗無需解釋。眾所周知，出口規格控制在±0.05mm以內。

　　Establishment of steel mesh scale, usually by the grid size is not particularly accurate, machinery is still a single requirement is more accurate, see the application requirements, generally in the 5mm diagonal, +2cm scale is normal, so welding, optical expansion and contraction will show that must be wrong. There is no need to explain the warp yarn of steel mesh. It is well known that the export specifications should be within (+0.05 mm).

　　網孔焊接加固。焊接點沒有固結形成鋼網，就像廢鐵一樣。非虛焊、漏焊。例如，兩個4mm的鋼網板焊接后的總高度應該在6mm到7mm之間。焊點太淺不牢固，焊點太深是網孔，沒有支撐，容易斷裂。這些都是在網目板質量查看過程中不可忽視的一些關鍵點，如果還有疑問可以繼續提問。

　　Mesh welding reinforcement. Welding joints are not consolidated to form a steel mesh, just like scrap iron. Non-virtual welding and leak welding. For example, the total height of two 4mm steel mesh plates after welding should be between 6mm and 7mm. The solder joint is too shallow and not firm. The solder joint is too deep and mesh hole. Without support, it is easy to break. These are some of the key points that can not be ignored in the process of checking the quality of the webpage. If you have any questions, you can continue to ask questions.